A Beginner's Guide to Installing a Bathtub
A Beginner's Guide to Installing a Bathtub
Blog Article
We have stumbled on this great article on Tools You Need to Install a New Bathtub listed below on the internet and reckoned it made good sense to share it with you on this site.
Setting up a bathtub isn't exactly brain surgery, however it does call for strong plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old tub with a brand-new one is also a moderately tough project. If the old tub is conveniently easily accessible, the project can move speedily; if you have to open up a wall to get rid of the old tub as well as place the new bathtub, the task is a lot harder. In either situation, the project is within a residence handyman's abilities, although you will require an assistant to vacate the old tub as well as set in the brand-new one. See to it you have actually certified on your own for the task as well as fit attempting it. Rather than employing a contractor to take control of a halfway-completed task, it is much better to consider employing one before you begin. Possibilities are you may require a specialist plumber to make tube links.
This article will certainly help you mount a new bath tub in your shower room if you have already acquired a new tub as well as do not require to change the plan of your previous water system pipelines.
Your devices and also material checklist should comprise the following:
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installment, after that the first thing you must do is detach the water system. After doing so, switch on the taps to drain pipes any kind of water remaining in the system. The process of removing the existing faucets can be rather troublesome as a result of the limited accessibility that is often the case.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a cloth prepared for the continuing to be water that will come from the pipelines. When the supply pipelines have actually been gotten rid of, make use of the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from turning throughout this procedure. Once the faucets have actually been removed, the holes in the bath/basin will need to be cleansed of any type of old sealing compound.
Prior to carrying on to fit the new faucets, compare the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic adapter to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the tap in the installing opening in the bath/basin ensuring that the washing machines remain in area between the faucet and the sink. Protect the tap in place with the manufacturer offered backnut. As soon as the tap is firmly in position, the supply pipes can be connected to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with regular tap ports. The previous kind needs to be connected to the tap finishes initially, tightening up only by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have been attached.
Installing the Bath tub
Using the two wooden boards under its feet, place the tub in the required placement. The wood boards are handy in equally spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto four little factors.
The following objective is to ensure that the bath tub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the bath tub up until the level reads degree.
To set up taps, fit all-time low of the furthest flexible tap adapter to the appropriate supply pipeline by making a compression join; then do the exact same for the other tap.
Switch on the water supply and also examine all joints and brand-new pipework for leakages and tighten them if necessary. Fill the bathtub as well as also examine the overflow electrical outlet and also the regular outlet for leaks.
Ultimately, take care of the bath paneling as described in the supplier's user's manual. Tiling and securing around the tub should wait till the bathtub has actually been used at the very least once as this will certainly settle it right into its last setting.
Getting ready for the Setup
First of all, the supporting frame provided with the bathroom must be fitted (if needed) according to the maker's directions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is important to see to it that if the tap comes with a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps device to avoid strain on the tub.
Fit the versatile faucet ports to the bottom of both taps utilizing 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet via the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you make use of every one of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom must currently be ready to be fitted in its last position.
Tiling Around the Bathtub
In the location where the bathroom meets the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to crack an inflexible seal, creating the water to pass through the wall between the bathroom as well as the tiling, leading to difficulties with wetness as well as feasible leaks to the ceiling below.
You can select from a range of coloured sealers to assimilate your fixtures and installations. They are offered in tubes as well as cartridges, and can sealing spaces up to a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly fill the tub with water prior to securing, to permit the movement experienced when the tub remains in usage. The sealer can fracture fairly early if you do not take into account this activity before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise conveniently readily available on the marketplace. It is recommended to fit the floor tiles using water-resistant or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a passionate person who reads on Installing A Bathtub, I thought sharing that section was important. Please take a moment to promote this post if you liked it. We cherish reading our article about Installing A Bathtub.
Information Here Report this page